Light O Rama Forum Picture Upload Info

The Standalone Sequence Downloader section of the LOR Control tab of the Light-O-Rama Hardware Utility tin can be used to send an animation sequence to a Light-O-Rama controller, which can later on run that sequence independently, in "standalone" style, without being hooked upward to a figurer running Light-O-Rama software.

When a unit runs a sequence in standalone way, it not only executes the lighting commands in the sequence that are for that controller itself, but also, if the sequence contains any commands for other units, information technology will transmit them to the other units that it is connected to.  In this way, a unmarried controller tin can be downloaded with a sequence, and act as a "director" for several linked controllers.

It is important that only one controller in any mutually connected group act as a managing director.  Downloading sequences to two dissever controllers that are hooked upward in a mutually connected grouping volition take undesired results, as the commands transmitted by the 2 volition interfere with each other.  Similarly, it is important not to also control sequences from your computer while y'all accept a controller hooked up to it interim in standalone manner, for the same reason.

Normally, the controller will execute the standalone sequence any time that it is powered on.  However, some controllers have internal clocks that let the standalone sequence to exist scheduled to run during a detail timeframe.

Notation: The CTB08 controller does not have transmit capability in standalone mode.

To download a sequence to a controller to exist used in standalone fashion, take the following steps:

•Create the Sequence

•Connect the Controller to the PC

•Select the Comm Port

•Select the Unit

•Download the Sequence

You lot can also use this department of the Hardware Utility to choose when the sequence will run (for controllers that support this), to remove the standalone sequence from a controller, and to examination a standalone sequence.

To go to the Standalone Sequence Downloader screen, make sure that you are in the LOR Control tab of the Hardware Utility, and so click on the "Standalone" button.

The Standalone Sequence Downloader section of the Hardware Utility

Create the Sequence

Using the Sequencer, create an animation sequence.  Only animation sequences - not musical sequences - can exist downloaded for standalone mode.  When you lot create the sequence, acquaintance it with a preview that has the appropriate unit IDs and excursion IDs, as normal.

Some controllers take very picayune storage space for sequences.  Considering size is a limiting cistron, y'all should consider the post-obit tips to keep your sequence's size at a minimum:

•Fade commands take upward the most space.

•The least space is used when all lights on a controller are at either 100% or 0% intensity.

•When possible, place similar commands at the aforementioned time.  For example, if you plow one circuit of a controller off then, a tenth of a 2nd later, plow some other excursion on the same controller off, that will have nearly twice equally much infinite every bit would turning both of them off at the aforementioned fourth dimension.

•Use loops whenever possible.

•Dissimilar types of controllers have dissimilar maximum sequence sizes; controllers such as the CTB08 take petty space and can handle but very elementary animations.

Besides, sequences to be used in standalone manner have some limitations:

•Yous must download the playback file (.play.las) created by the Sequencer.

•The sequence's preview should only incorporate props that are on a single network; unexpected results may occur if you take more than 1 network listed in the preview.

•The network must not be marked as "enhanced" in Network Preferences.

•The sequence cannot contain motion effects.

•Timings are merely supported on tenth-of-a-second boundaries (for example, 1 second, 1.one seconds, ane.2 seconds).  If any timings in the sequence are at some centisecond other than a 10th-of-a-2d boundary (for example, 1.15 seconds), they volition exist considered to be at the adjacent 10th-of-a-2d boundary.

•Depending on the device type, between 1 and 10 loop levels may exist supported.

•Loop speed modification is non supported, and volition be ignored.

Connect the Controller to the PC

Connect the unit to the calculator, for case using an SC485 adaptor or a USB-RS485 adaptor.  Make sure that the selector switches are correctly set for the blazon of cable used (units are shipped set to apply data cables).  Plug the unit into an AC outlet, and plow the unit on.

Select the Comm Port

After you take connected the unit of measurement to the computer, select the comm port that the Hardware Utility should use to communicate with the controller.

Select the Unit

Afterwards you lot take connected the unit to the PC and selected the comm port, select the unit ID of the controller that you wish to utilize.  If you know the controller's unit of measurement ID, you can simply type it into the dropdown box labelled "Select Unit".  If not, use the "Refresh" button, and the Hardware Utility will browse your network for connected units.  You can then select information technology from the dropdown list.

NOTE: Scanning the network may accept some fourth dimension.  If you have fix the unit IDs of your controllers to low values, y'all tin utilise the "Max Unit of measurement ID" section to speed upward this scan drastically.  Information technology is therefore a skilful habit to assign your controllers unit IDs starting at 01, and increasing sequentially through 02, 03, and so on.

Selecting the unit to use

Download the Sequence

Choose the animation sequence you wish to download using the "Open" push button in the "Select Sequence" section, and then download it using the "DownLoad" push button in the "Download Selected Sequence" section:

Selecting and downloading the sequence

If you lot do not see this in the Hardware Utility, make sure that you are on the LOR Control tab, and click on the "Standalone" button near the bottom.

Scheduling the Sequence

Some Light-O-Rama controllers can schedule the downloaded sequence to run at sure times or in sure weather (those that cannot will run the sequence continually whenever powered on).  To schedule when information technology will run, utilize the "Trigger Status" section:

Scheduling the sequence

Select the status yous desire to start the sequence, and click "Ship Trigger info to Unit of measurement".

If you do non come across this in the Hardware Utility, make sure that you lot are on the LOR Control tab, and click on the "Standalone" button near the bottom.

Note: If you choose to use specific scheduled times, the clock on the controller is set to the electric current time co-ordinate to your estimator.  Make sure that the fourth dimension on your computer is correct.

Removing the Sequence

To remove a downloaded sequence from a standalone controller, use the "Delete" push in the "Remove Sequence" section:

Removing a sequence

Notation: This does not actually remove the sequence from the controller; rather, it makes it and then that the controller will no longer play the sequence.  So, if you after make up one's mind to use the sequence once again, you can just reschedule the sequence to run, rather than downloading the sequence again.

If yous practise not see this in the Hardware Utility, brand sure that yous are on the LOR Control tab, and click on the "Standalone" push button near the lesser.

Testing the Sequence

After downloading a sequence to a controller to be used in standalone mode, it is recommended that you lot exam the sequence, using the buttons in the "Test Sequence" section.  To outset the sequence, click "Sequence ON"; to cease information technology, click "Sequence OFF".

Note that the "Sequence OFF" push will stop the sequence even if it was started automatically (by powering on or by schedule, as opposed to via the "Sequence ON" push).

Testing the sequence

If you do not see this in the Hardware Utility, brand certain that y'all are on the LOR Control tab, and click on the "Standalone" button near the bottom.

burkharteastring.blogspot.com

Source: http://www.lightorama.com/help/downloading_sequences.htm

Share this post